Cart Total: $0
View Cart | Checkout
    https://installationpartssupply.com/mm5/merchant.mvc?

     HOME > BAR GUNS & DISPENSERS > Soda Carbonation Tester | Taprite

Soda Carbonation Tester | Taprite


Soda Carbonation Tester | Taprite

Soda Carbonation Tester | Taprite 2701, 2701G
The Taprite Pepsi and Generic Carbonation Testers are a great tool for verifying and maintaining CO2 levels in sugared Pepsi and other soda products. Simply put a sample of your beverage into the tester’s 11 ounce acrylic canister, record the pressure and temperature from the easy to read gauges, and cross-reference your findings with the data on the handy carbonation table.
  • Scroll to bottom for info on the Generic Tester or click the part # in the list
  • Cap and fittings are made of lightweight, anodized aluminum with easy to grip knurling
  • Pressure gauge includes a protective rubber boot (600GPS-01) for additional durability
  • Easy to handle, easy to use, and easy to clean
  • Affordably priced
  • Log In For Your Wholesale / Volume Price Before Adding to Cart
  • Contact IPS For Volume Quotes & Other Options Click Here! sales@ips247.com
  • Click the part # in the list below for image, info and a closer look
  • Scroll for more Info, Specs & Related Items.
  • 3-5 Day ETA for Out of Stock/Non-Stock Items in this Category
Click Here for Calibration and Operating Instructions
Part # Soda Carbonation Tester | Taprite
Stock
Price
Qty
2701 Soda Carbonation Tester for Pepsi Sugared Products Taprite 2701
Out of Stock  
$118.42
2701G Soft Drink Carbonation Tester (Generic) Taprite 2701G
Out of Stock  
$118.42

The Taprite Soft Drink Carbonation Tester is a great tool for verifying and maintaining CO2 levels in sugared soft drinks. Simply put a sample of your beverage into the tester’s 11 ounce acrylic canister, record the pressure and temperature from the easy to read gauges, and cross-reference your findings with the data on the handy carbonation table. The Tester’s cap and fittings are made of lightweight, anodized aluminum with easy to grip knurling. The pressure gauge includes a protective rubber boot (600GPS-01) for additional durability. Taprite’s Soft Drink Carbonation Tester is easy to handle, easy to use, and easy to clean, and is a must have for every Field Service Technician.
  • Simple and easy to use
  • Fewer parts makes cleaning easy
  • Plastic canister won't conduct heat
  • Fittings are all stainless or plated metal
  • Pre-calibrated and easy to read components
  • Cost is much less than competitor's models available
  • Comes with its own carrying case
  • Taprite Soda Carbonation Tester General Information
  • Use an NIST (National Institute for Standards and Technology) reference thermometer to calibrate the carbonation tester thermometer at or near the sample testing temperature.
  • Use an NIST certified dead weight tester or an NIST certified pressure gauge calibrator.
  • Do not turn the hex nut when calibrating the thermometer. The hex nut immediately below the head of the thermometer is used to hold the thermometer while turning the head to calibrate.

  • Taprite Carbonation Tester Operating Instructions
  • Ensure that the pressure gauge and thermometer are calibrated prior to conducting a carbonation test.
  • Chill both halves of the carbonation tester in an ice cold water bath. Do not submerge the pressure gauge or thermometer.
  • Open the relief valve by flipping the yellow toggle to a vertical position.
  • Empty the contents of the carbonation tester
  • Tilt the canister to 45 degrees and fill the canister to the scribed line located inside the canister. The fountain drink should flow steadily down the side of the canister to minimize foaming.
  • Place the canister on a horizontal surface and carefully screw on the cap.
  • Once the cap bottoms close the relief valve and tighten the cap a quarter turn.
  • Gently swirl the tester until a pressure of 5 psig +/-1 psig is indicated on the gauge.
  • Purge the carbonation gas by opening the relief valve; the pressure should drop down to zero
  • Close the relief valve
  • Vigorously shake the carbonation tester for 30 seconds
  • Determine the volume (%) of carbonation from the canister chart by reading the value at the temperature/pressure intersection.
  • Open the relief valve and empty the contents of the tester
  • Wash the tester in a warm mild detergent and then dry thoroughly
  • Follow Installation Parts Supply.com® on:

    Terms & Conditions | Privacy Policy | Email | Contact IPS
    Pumps | Water Filters | Pressure Regulators | Backflow Preventers | Carbonators | Cold Plates | Dispensers
    Taprite CO2 Regulators | Oetiker Clamps | Tubing & Hose | Brass Fittings | Stainless Fittings | John Guest Fittings
    Bottle Water Pumps | Beer Equipment | Electrical Hardware

    TOP OF PAGE | HOME | Google

    © 2016 INSTALLATION PARTS SUPPLY® All Rights Reserved.
    ALL COPYRIGHTS AND TRADEMARKS ARE THE PROPERTY OF THEIR RESPECTIVE COMPANY(S).
    IPS claims no ownership or rights of listed Logo's, Names or Products other than; IPS, its Company Logo, and INSTALLATIONPARTSSUPPLY.COM®.


    Some of the products listed on InstallationPartsSupply.com® may contain chemicals
    known to the State of California, Vermont and other states to cause cancer, birth defects or other reproductive harm.
    Some of the products, may or may not meet AB1953 for lead content.
    It is the customers/buyers and ultimately the user/installers responsibility to be aware of and know all laws pertaining to the use of specific products such as Backflow Preventers
    IPS is a distributor, not a manufacturer and IPS-Installation Parts Supply.com and its principles shall be held harmless of any and all damages including but not limited to:
    legal action for misuse, physical, property, water damage or otherwise for any reason. Purchaser/user/installer claims, bears and holds all responsibility.
    Some Images are for illustration only and are subject to change according to current inventory and/or Factory Production. Prices subject to change with market fluctuation.
    With purchase, The Customer agrees to all terms and conditions as outlined here and on IPS247.com® Terms and Conditions.


    Credit Cards
    PCI Compliance


    *Local Will Call Hours: 9:00am - 3:00pm Pacific
    *DUE TO INSURANCE PURPOSES, LOCAL WILL CALL ORDERS MUST BE PLACED VIA THE WEBSITE.
    We will pull your order and have it ready for you to pick-up within Will Call hours.
    Please allow at least 1 (one) hour to process your order after it has been placed prior to will call.
    (Select "Local Will Call" when prompted to choose a Shipping Method; Email IPS if this option is not available)
    All Will Calls/Pick Ups and Deliveries are at the "Man Door" on Side of Building @ Shipping Department.
    Switch to Mobile