Home > PUMPS & ACCESSORIES > Flojet Pumps & Accessories > Air and Gas Powered Pumps G, K & T Series Flojet > G60 WaterJet Water Boost
G60 WaterJet Water Boost
Model: G60-1212I
- Inlet; 1/2” (9.52 mm) Barbed 90° Elbow Plastic (Polypropylene)
- Outlet: 1/2” (9.52 mm) Barbed 90° Elbow Plastic (Polypropylene)
- Gas Inlet; 1/4" (6.35 mm) CO2 Shutoff Brass
- Design; Positive Displacement, Double Diaphragm
- Power Source; CO2 Gas, Nitrogen or Compressed Dry Filtered Air
- Construction; Polypropylene, Santoprene®, EPDM, AISI 303 & 304 Stainless Steel
- Limits; 34? to 120? F (1.1? to 49? C)
- Weight; 1.24 lb (0.56 kg)
- Dimms; 5.27" x 3.21" x 4.58"(133.8 mm x 81.5 mm x 116.3 mm)
- Displacement; 3.2 oz. per cycle
- Self Priming; Up to 10 ft.(3.05 m)
- Operating Pressure; 20 psi (1.4 bar) min. / 90 psi (6.2 bar) max.
- Liquid Inlet Pressure; 30 psi(2.1 bar) max.
- Flow Rate; 5 GPM (18.9 LPM) - Open Flow
- Click the part # below for specific info and a closer look
Products (Total Items: 1)
Model: G60-1212I
Water Boosting can be necessary either in areas of poor water pressure or where there can be many machines demanding water and therefore water pressure can fluctuate. If water pressure does fluctuate it can affect the drink BRIX value and therefore can directly affect taste. Flojet water booster systems provide consistent pressure up to 150 PSI (10 Bar).
Water boosting for filtration systems, supply carbonators, non-carbonated dispensing valves, carts, coffee machines, hand sinks, ice machines and FCB equipment. Supplies up to 4 GPM (15 L /min). Note: If pumping over 1.7GPM (6.4 L /min), a pulsation dampener or accumulator tank should be utilized to reduce pulsation, due to momentary shifts in flow requirements.
Special Features:
Water Boosting can be necessary either in areas of poor water pressure or where there can be many machines demanding water and therefore water pressure can fluctuate. If water pressure does fluctuate it can affect the drink BRIX value and therefore can directly affect taste. Flojet water booster systems provide consistent pressure up to 150 PSI (10 Bar).
Water boosting for filtration systems, supply carbonators, non-carbonated dispensing valves, carts, coffee machines, hand sinks, ice machines and FCB equipment. Supplies up to 4 GPM (15 L /min). Note: If pumping over 1.7GPM (6.4 L /min), a pulsation dampener or accumulator tank should be utilized to reduce pulsation, due to momentary shifts in flow requirements.
Special Features:
- Capable of CO2 inlet pressures, up to 90 psi (6.2 bar)
- Ultimate performance and reliability, with extended service life
- Quiet operation
- Easy installation with quick disconnect ports
- Inlet; 1/2” (9.52 mm) Barbed Straight Plastic (Polypropylene)
- Outlet: 1/2” (9.52 mm) Barbed Straight Plastic (Polypropylene)
- Gas Inlet; 1/4" (6.35 mm) CO2 Shutoff Brass
- Design; Positive Displacement, Double Diaphragm
- Power Source; CO2 Gas, Nitrogen or Compressed Dry Filtered Air
- Construction; Polypropylene, Santoprene®, EPDM, AISI 303 & 304 Stainless Steel
- Limits; 34? to 120? F (1.1? to 49? C)
- Weight; 1.24 lb (0.56 kg)
- Dimms; 5.27" x 3.21" x 4.58"(133.8 mm x 81.5 mm x 116.3 mm)
- Displacement; 3.2 oz. per cycle
- Self Priming; Up to 10 ft.(3.05 m)
- Operating Pressure; 20 psi (1.4 bar) min. / 90 psi (6.2 bar) max.
- Liquid Inlet Pressure; 30 psi(2.1 bar) max.
- Flow Rate; 5 GPM (18.9 LPM) - Open Flow